Description Key Technical Specifications Parameter Specification Part Number Z7128 Product Type Power Supply Module Series HIMax Safety System Input Voltage 24V DC nominal (19.2-30V DC range) Input Current Dependent on load (rated for system requirements) Output Power Rated for HIMax backplane and modules Output Voltages Regulated DC to backplane Efficiency >90% typical Redundancy Supported (1 1 or N 1 configurations) Hot Swap Supported (online replacement) Protection Overcurrent, overvoltage, overtemperature, reverse polarity Isolation Input-to-output galvanic isolation Indicators Power OK, fault, redundancy status LEDs Cooling Convection (no fan) Mounting HIMax rack (dedicated slots) Operating Temp 0°C to 60°C Certifications TÜV SIL3, PL e Condition New Surplus (Original Packaging) Product Introduction The HIMA Z7128 is a power supply module for the HIMax safety system, providing regulated DC power to the backplane, main processors, and I/O modules in high-integrity safety applications such as emergency shutdown (ESD), fire and gas, burner management, and turbine control. It accepts 24V DC input and delivers clean, isolated power to the entire HIMax rack. The Z7128 features high efficiency and convection cooling for silent, reliable operation in safety-critical environments. Redundant configurations (1 1 or N 1) allow continuous operation if one supply fails. Hot-swap capability enables module replacement without shutting down the safety system. This unit is new surplus, factory-sealed in original HIMA packaging. HIMax components are engineered for SIL3 applications; contact us for current stock and firm pricing. Frequently Asked Questions (FAQ) Q: What is the HIMax system, and where is the Z7128 used? A: HIMax is HIMA’s high-integrity safety system platform, designed for SIL3 applications in process, power, and railway industries. The HIMA Z7128 is the power supply module that provides DC power to the HIMax rack. You’ll find it in: Emergency shutdown (ESD) systems Fire and gas detection systems Burner management systems (BMS) Turbine and compressor control Railway signaling and interlocking The Z7128 is the foundation of the system—without reliable power, nothing else works. Q: Does the Z7128 support redundant power supply configurations? A: Yes. The HIMax system supports multiple Z7128 modules in the same rack for redundancy: 1 1 redundancy: Two supplies, each capable of powering the entire rack. If one fails, the other takes over. N 1 redundancy: Multiple supplies sharing load, with one extra for backup. Redundancy requires proper configuration and external wiring (typically via diode isolation or the HIMax backplane’s built-in redundancy features). In SIL3 applications, redundant power is standard—single points of failure are not allowed. The Z7128 is designed for this. Q: What input voltage does the Z7128 require? A: The HIMA Z7128 accepts 24V DC nominal, with a range of 19.2-30V DC. This is standard industrial control voltage. The input must come from a safety-rated power supply (often redundant 24V DC supplies with battery backup). The Z7128 does NOT accept AC input directly—you need an external AC/DC converter if your plant power is AC. For critical safety systems, the 24V DC supply itself is often redundant and monitored. Q: What do the front panel LEDs indicate on the Z7128? A: The Z7128 has multiple status LEDs: PWR (green): Input power present, module operational FAIL (red): Internal fault (output out of range, overtemp, etc.) RED (green): Redundancy active (if configured with partner) In normal operation, PWR is green, FAIL off. If FAIL lights, the has detected an internal problem—replace at next opportunity if redundant, immediately if single. If PWR is off, check input 24V DC and wiring. Q: Is the Z7128 hot-swappable in a live HIMax rack? A: Yes, with redundant configuration. The HIMA Z7128 supports hot-swapping (online replacement) when installed in a redundant pair or group. Procedure: Verify redundant partner(s) are healthy and carrying the load Remove faulty Insert new module Verify its PWR LED illuminates and FAIL stays off System continues without interruption For single-supply configurations (not recommended in safety systems), hot-swap is not possible—the rack loses power. In SIL3 applications, we always use redundant power supplies. Q: What’s the difference between Z7128 and other HIMax power supplies (like Z7127)? A: The is typically the standard 24V DC input version. Other part numbers (Z7127, Z7129, etc.) may indicate: Different input voltage ranges (e.g., 48V DC, 110V DC, 230V AC with external converter) Different output power capacity Special certifications (marine, nuclear) Hardware revisions Always match the exact part number from your existing system. In HIMax, power supply variants are not interchangeable without engineering verification. The is the most common for 24V DC plants. Q: What’s the typical failure mode for Z7128 modules? A: In my experience with HIMax systems: Capacitor aging—after 10-15 years in warm cabinets Input surge damage—lightning or switching transients on 24V DC lines Internal regulator failure—one of the DC-DC converters dies Connector corrosion in harsh environments (offshore, chemical) The HIMA Z7128 is built for safety systems, but nothing lasts forever. If the FAIL LED lights or the module stops outputting power, replace it immediately. In redundant systems, you can wait for a scheduled outage; in single-supply systems, failure means rack shutdown—replace NOW. Q: Can the Z7128 be used in SIL2 applications, or is it only for SIL3? A: It’s certified for SIL3, but you can use it in SIL2 applications—it’s overkill but works fine. The doesn’t care what safety level you’re targeting. However, its diagnostics and reliability are designed for SIL3. If your application only needs SIL2, you’re paying for capability you don’t use. Many plants standardize on across all safety functions for spares commonality. That’s fine—the module doesn’t degrade in lower-SIL use. Q: Does the Z7128 require configuration software? A: No. The HIMA Z7128 is hardware-only—no software configuration. It simply provides power. However, the HIMax system monitors its status via the backplane. The safety controller can detect and report power supply faults, redundancy status, and alarms to operators. This monitoring is automatic—no configuration required beyond standard system integration. Q: What cooling does the Z7128 use? A: The uses convection cooling—no fan. This is intentional for safety systems: fans are moving parts that fail. Convection cooling means: No fan noise No moving parts to wear out Requires adequate airflow around the module Must not block ventilation slots In HIMax cabinets, we ensure proper spacing and airflow. The is rated for full load without fans, but don’t pack modules tightly without ventilation. In hot environments, cabinet cooling may be needed. Q: What maintenance does the Z7128 require? A: Minimal but important: Annual visual inspection for bulging capacitors, discoloration, or odor Check input voltage quality (should be stable 24V DC ±10%) Verify PWR LED is green during routine rounds Ensure ventilation slots are clear of dust In redundant systems, test failover periodically (simulate one supply failure to verify the other takes over) The is designed for long life, but preventive maintenance catches problems before they cause outages. In one refinery, we found a with elevated ripple during testing—replaced it proactively before failure. Q: Can the Z7128 power multiple HIMax racks? A: No. Each HIMax rack requires its own power supply or set of redundant supplies. The mounts in a specific rack and powers that rack’s backplane only. For multi-rack systems, each rack has its own power supplies. Expansion cables carry signals, not power. In large safety systems, we calculate power per rack and size accordingly. The is rated for its own rack’s maximum configuration. DIC-64-B-39050-PCB PLC PRD-P306250E-45 PLC MPL-B320P-SJ22AA PLC 09F5B3A-390A PLC AEG-AM80NY4 PLC Email: [email protected] Phone: 86 15340683922 Sales:Wu Jiedong Our products are guaranteed for 1 year, with new and original production stopped and imported spare parts. All prices listed on the official website are subject to confirmation by contact: Wu Jiedong (manager). Our product: brand new original packaging Our warranty: All new or repaired parts have a 12 month warranty period beginning Our payment: 100% telegraphic transfer of inventory items before shipment, conditions can be proposed! If you have any downtime spare parts that you cannot find, please feel free to call or use email to contact me. If there are issues that the product cannot solve, please contact me. Product prices can be negotiated. Please do not consider contacting me!